HP0-M33 PDF Test: Most Reliable HP0-M33 PDF Study Guide And Latest HP0-M33 Questions

Exam A
Users report that all external callers are leaving urgent voice-mail messages. Where can this behavior be changed?
A. under the Phone Menu Configuration > Unidentified Callers Message Urgency
B. under the Opening Greeting > Unidentified Callers Message Urgency
C. under the Message Settings > Unidentified Callers Message Urgency
D. under the System Call Handlers > Unidentified Callers Message Urgency
E. under the Voice-mail Box Settings > Unidentified Callers Message Urgency
Correct Answer: C
Which two fields are required parameters when manually creating users on Cisco Unity Connection with predefined templates.? (Choose two.)
A. username (alias)
B. extension
C. first name and last name
D. employee ID
E. title
Correct Answer: AB
An administrator is attempting to add a new user in Cisco Unified Communications Manager Administration
but does not see the option to add a new user.
What is the most likely cause of this issue?

A. The SQL User database is not running.
B. The system is synchronized with an LDAP server.
C. BAT is not enabled.
D. The administrator hasthe aceno user adda rights box checked.
E. The SIP Realm is not defined in User Management.
Correct Answer: B

Which call processing agent is based on Cisco IOS software and works with ISR platforms?
A. Cisco Unified Presence Server
B. Cisco Unity Connection
C. Cisco Unified Communications Manager Express
D. Cisco Unified Communications Manager
E. Cisco Unified Contact Center Express
Correct Answer: C
Which two options allow the maximum message length to be adjusted in Cisco Unity Connection? (Choose two.)
A. Message Settings under individual users
B. User Templates >VoiceMailUserTemplate > Message Settings
C. Contacts > Message Settings
D. Enterprise Parameters > Maximum Message length
E. Service Parameters > Voicemail Settings
Correct Answer: AB
An administrator wants to locate and remove all unassigned directory numbers on the Cisco Unified
Communications Manager system.
Which method is the best method to accomplish this task?

A. Choose Device > Phone. Search all phones and remove the undesired directory numbers.
B. Use the Dial Plan Installer to remove the directory numbers.
C. Use the Disaster Recovery System to restore only valid directory numbers.
D. Choose Call Routing > Route Plan Report, choose the Unassigned DN drop-down menu, and then remove all orphaned directory numbers.
E. Choose Device > Device Settings > Device Defaults and use the wizard to locate and remove the orphaned directory numbers.
Correct Answer: D
When troubleshooting a phone that is unable to get an IP address from a DHCP server, what is the first thing to check for on the phone?
A. Make sure that DHCP Enabled is disabled on the phone.
B. Make sure that the phone is getting the proper VLAN information
C. Make sure that the TFTP server address is correct on the phone.
D. Make sure that the DHCP scope has enough addresses left in the range.
E. Make sure the phone has the correct phone load ID.
Correct Answer: B
Which issue does CAS signaling on a T1 circuit create?
A. Signaling bits are subtracted from each frame, which causes a significant loss of voice quality.
B. An extra signaling bit is added to the sixth frame to carry signaling information.
C. A signaling bit is subtracted from every sixth frame to carry signaling information.
D. Signaling bits are added to the signaling stream to create extended super frames.
Correct Answer: C

Which description describes the weighted fair queuing algorithm?
A. Empty queue 1. If queue 1 is empty, empty queue 2, then empty queue 3, unless a packet for a higher queue arrives.
B. An administrator defines the traffic classes based on match criteria, including protocols, access control lists, and input interfaces.
C. A flow-based algorithm that simultaneously schedules interactive traffic to the front of a queue to reduce response time and fairly shares the remaining bandwidth among high-bandwidth flows.
D. This feature brings strict priority queuing to CBWFQ.
E. Packets are placed into a single queue and serviced in the order they were received.
Correct Answer: C
Which utility should you use when you need to add a large number of users into Cisco Unified Communications Manager?
A. Cisco Unified User Administration
B. Application User CAPF Profile
C. Cisco Unified Communications Manager Bulk Administration Tool
D. Cisco Unified Telephony User Administration
Correct Answer: C