Valid Cisco 350-001 Exam Practice Test To Pass Exam Easily Free Download With All New Latest Exam Questions 100% Pass
Exam A QUESTION 1
In order to maintain security, with which hop count are IPv6 neighbor discovery packets sent?
Correct Answer: C QUESTION 2
Which command will define a VRF with name ‘CCIE’ in IPv6?
A. ip vrf CCIE
B. ipv6 vrf CCIE
C. vrf definition CCIE
D. ipv6 vrf definition CCIE
Correct Answer: C QUESTION 3
For which routes does LDP advertise a label binding?
A. all routes in the routing table
B. only the IGP and BGP routes in the routing table
C. only the BGP routes in the routing table
D. only the IGP routes in the routing table
Correct Answer: D QUESTION 4
Which command can be used on a PE router to connect to a CE router (188.8.131.52) in VRF red?
A. telnet 184.108.40.206 /vrf-source red
B. telnet 220.127.116.11 source /vrf red
C. telnet 18.104.22.168 /source vrf red
D. telnet 22.214.171.124 /vrf red
E. telnet 126.96.36.199 vrf red
Correct Answer: D QUESTION 5
Refer to the exhibit.
***Exhibit is Missing***
This is an MPLS VPN network with OSPF as the PE-CE routing protocol. Which statement is correct?
“First Test, First Pass” – www.lead2pass.com 4
A. The routing inside the VPN RED will never work correctly.
B. The routing inside the VPN RED can be enabled by configuring virtual links between the PE routers.
C. The routing inside the VPN RED can be enabled by configuring area 0 inside the VRF on the PE routers.
D. The routing inside the VPN RED will work without any special OSPF configuration.
E. The routing inside the VPN RED will work if the PE routers have a full mesh of sham-links configured for VRF RED.
Correct Answer: D
Which two statements are correct about Nonstop Forwarding? (Choose two.)
A. It allows the standby RP to take control of the device after a hardware or software fault on the active RP.
B. It is a Layer 3 function that works with SSO to minimize the amount of time a network is unavailable to users following a switchover.
C. It is supported by the implementation of EIGRP, OSPF, RIPv2, and BGP protocols.
D. It synchronizes startup configuration, startup variables, and running configuration.
E. The main objective of NSF is to continue forwarding IP packets following a switchover.
F. Layer 2 802.1w or 802.1s must be used, as 802.1d cannot process the Layer 2 changes.
G. Routing protocol tuning parameters must be the same as the NSF parameters, or failover will be inconsistent.
Correct Answer: BE
Which three fields are optional in an OSPFv3 external LSA? (Choose three.)
A. Forwarding Address
B. External Route
C. Reference Link-State ID
E. Prefix Options
Correct Answer: ABC
On a router, interface S0 is running EIGRPv6, and interface S1 is running OSPFv3. A redistribution command is issued under OSPFv3, redistribute EIGRP 1 metric 20 under ipv6 router nospf 1. What will happen after applying this redistribution command?
A. All routes showing up as D and D EX in the routing table will be redistributed into OSPFv3.
B. All routes showing up as D, D EX, and C in the routing table will be redistributed into OSPFv3.
C. All routes showing up as D and D EX in the routing table and the S0 interface will be redistributed into OSPFv3.
D. All routes showing up as D in the routing table will be redistributed into OSPFv3.
E. All routes showing up as D EX in the routing table will be redistributed into OSPFv3. “First Test, First Pass” – www.lead2pass.com 5
Correct Answer: A
Which type of domains is interconnected using Multicast Source Discovery Protocol?
Correct Answer: A
Which two multicast address ranges are assigned as source-specific multicast destination addresses and are reserved for use by source-specific applications and protocols? (Choose two.)
Correct Answer: AD QUESTION 11
How is RPF used in multicast routing?
A. to prevent multicast packets from looping
B. to prevent PIM packets from looping
C. to instruct PIM where to send a (*,G) or (S,G) join message
D. to prevent multicast packets from looping and to instruct PIM where to send a (*,G) or (S,G) join message
Correct Answer: D