Cisco 350-001 Cert Exam, Recenty Updated Cisco 350-001 Certification Braindumps With The Knowledge And Skills

100% Pass!Do you want to pass Cisco 350-001 exam quickly? Go to flydumps.com to get more free exam dumps.All the Cisco 350-001 dumps are timely updated by the professional experts.Also we guarantee 100% pass and money back guarante

QUESTION 11
How is RPF used in multicast routing?
A. to prevent multicast packets from looping
B. to prevent PIM packets from looping
C. to instruct PIM where to send a (*,G) or (S,G) join message
D. to prevent multicast packets from looping and to instruct PIM where to send a (*,G) or (S,G) join message

Correct Answer: D QUESTION 12
Refer to the exhibit.
***Exhibit is Missing***
What does the incoming interface of the above (*,G) entry indicate?

A. the interface closest to the source, according to the unicast routing table
B. the interface where an IGMP join has been received
C. the interface with the highest IP address
D. the last interface to hear a PIM (*,G) join
E. the interface closest to the RP, according to the unicast routing table

Correct Answer: E QUESTION 13
Refer to the exhibit.
***Exhibit is Missing***
Which interface(s) will show ip rpf 1.1.1.2 indicate as RPF interface(s)?

A. Ethernet 1/0
B. Ethernet 0/0
C. Both Ethernet 0/0 and Ethernet 1/0
D. RPF will fail

Correct Answer: A QUESTION 14
Apart from interdomain multicast routing, what else is MSDP used for?
A. Source Specific Multicast and IGMPv2
B. Announcing multicast sources to BGP speakers
C. Anycast RP
D. Intradomain multicast routing

Correct Answer: C QUESTION 15
Which IGMPv2 message contains a non-zero “Max Response Time”?
A. Membership Query
B. Membership Report
C. Membership Delay
D. Backward Compatible IGMPv1 Report Message

Correct Answer: A QUESTION 16
Refer to the exhibit.
***Exhibit is Missing***
Which IGMPv2 message is displayed in the output of the packet capture?

A. General Query
B. Membership Report
C. Membership Query
D. Membership Delay

Correct Answer: B QUESTION 17
What is Phantom RP used for?
A. it is used for load balancing in bidirectional PIM
B. it is used for redundancy in bidirectional PIM
C. it is used for redundancy in PIM-SM
D. it is used for load balancing in PIM-SM

Correct Answer: B QUESTION 18
Which three statements are true about TACACS+? (Choose three.)
A. It is a Cisco proprietary protocol.
B. It runs on TCP port 59.
C. Authentication and authorization are done at different stages.
D. TACACS+ encrypts the entire body of the packet, but leaves a standard TACACS+ header.
E. It is an industry standard protocol.
F. TACACS+ encrypts both the entire body of the packet and the TACACS+ header.

Correct Answer: ACD QUESTION 19
Refer to the exhibit.
***Exhibit is Missing***
Which two statements are correct? (Choose two.)

A. The hexadecimal value of the number of packets that hit the access list is 0x723E6E12.
B. The access list has logging enabled.
C. The packet was discarded.
D. The command ip access-list logging hash-generation is enabled.
E. The Telnet connection is successfully set up.

Correct Answer: BD QUESTION 20
Refer to the exhibit. ***Exhibit is Missing*** Which statement is correct?
A. This configuration is not valid.
B. Control Plane Policing is configured; however you cannot determine on which interface it is configured.
C. NTP is not configured on the router.
D. Telnet traffic will be dropped.

Correct Answer: C

Cisco 350-001 Questions and Answers Products basically comprise of the simulated Cisco 350-001 exam questions AND their most correct answers,accompanied with a methodical elucidation of the Cisco 350-001 answers and the probable wrong answers.The extent to which Cisco 350-001 Questions and Answers Products cover their Cisco subject is so thorough,that once you are done with a Cisco product,passing the Cisco 350-001 exam in first attempt should be a piece of cake.